The MARIPUR 7100 is a colored, one component, highly durable, aromatic polyurethane thin-layer floor coating.
The MARIPUR 7100 is specially designed for use as a floor coating, providing high mechanical strength, high abrasion and chemical resistance.

Cures by reaction with ground and air moisture.


  • Simple application (roller or airless spray).
  • High abrasion resistant.
  • Decorative.
  • Resistant to constant, heavy abrasion and wear conditions.
  • Heat and frost resistant
  • When applied does not absorb liquids or dirt
  • Stops the creation of dust
  • Gives a glossy and easy-to-clean surface
  • Chemical resistant
  • Maintains its mechanical properties over a temperaturespanof-40C to +90C


The MARIPUR 7100 is mainly used on concrete floors, on interior surfaces.
Due to its long lasting unchangeable properties is widely used for:

  • Car repair garages,
  • Car parking areas,
  • Warehouses,
  • Storage rooms,
  • Factories,
  • Animal breading farms,
  • Cold storage rooms (Freezers), etc


300 gr/m2 in two layers. This coverage is based on practical application by roller onto a smooth surface in optimum conditions. Factors like surface porosity, temperature, humidity, application method and finish required can alter consumption.


The MARIPUR 7100 is supplied in light grey, dark grey and beige. Other RAL colors supplied on request.

Technical data

PROPERTY RESULTS TEST METHOD Composition Pigmented Polyurethane pre-polymer. Solvent based Elongation at Break >50 % DIN 53504

Tensile Strength >3 N/mm2 DIN 53504 Adhesion to Concrete >2 N/mm2 ASTM D 903 Hardness (SHORE D Scale) 20 ASTM D 2240 Resistance to Water Pressure No Leak (1m water column, 24h) DIN EN 1928 Application Temperature 5C to 35C Conditions: 20C, 50% RH Tack Free Time 2-3 hours Conditions: 20C, 50% RH Light Trafficking 12-24 hours Conditions: 20C, 50% RH Final Curing time 7 days Conditions: 20C, 50% RH

Chemical properties

Potassium hydroxide 5% + Sodium hydroxide 5% + Ammonia 5% + Sulfuric acid 5% + Hydrochloric acid 5% + Sea water + Domestic detergents (diluted) + Dichlormethane – Diesel fuel + N-methyl pyrrolidone (brake fluid) – {+ Stable, – Not stable, Stable for a short period.


Surface Preparation

The surface needs to be clean, dry and sound, free of any contamination, which may harmfully affect the adhesion of the membrane. Maximum moisture content should not exceed 5%. Substrate compressive strength should be at least 25MPa, cohesive bond strength at least 1.5MPa. New concrete structures need to dry for at least 28 days. Old, loose coatings, dirt, fats, oils, organic substances and dust need to be removed by a grinding machine. Possible surface irregularities need to be smoothened. Any loose surface pieces and grinding dust need to be thoroughly removed.
WARNING: Do not wash surface with water!
WARNING: Do not use a metal-ball blasting machine to grind the surface, because the heavy metal-ball impacts destroy the cohesion of the concrete surface and lower its stability.

Repair of cracks:

Clean cracks and hairline cracks, of dust, residue or other contamination. Fill all cracks with suitable putty. The next day smoothen the putty surface with a sandpaper or a mechanical grinder.

Absorbent surfaces

Prime absorbent surfaces, like concrete, cement screed and wood with the MARIPUR® 7000 primer, for the first layer by using a roller, brush or a spray gun.
After 2-3 hours (not later than 4 hours) and while the primer is still a bit tacky, apply the first layer, of the coloured MARIPUR 7100 coating.

Once again allow 3-4 hours for the coating to cure (not more then 4 hours) and apply the second layer of the coloured MARIPUR 7100.

Non-absorbent surfaces

Prime non-absorbent surfaces like metal, terrazzo, mosaic, specific types of power-floated concrete and ceramic tiles with the MARIPOX 2510 Primer, for the first layer by using a roller, or a brush.
After 12 hours (not later than 18 hours) apply the first layer, of the coloured MARIPUR® 7100 coating.
Once again allow 3-4 hours for the coating to cure (not more then 4 hours) and apply the second layer of the coloured MARIPUR 7100.

Stir well before using. For best results, the temperature during application and cure should be between 5C and 35C. Low temperatures retard cure while high temperature speed up curing. High humidity may affect the final finish.

Anti-slip Finish

In order to achieve an anti-slip effect we need to evenly sprinkle corundum (or silica sand) on the first layer of MARIPUR® 7100while still wet. When the layer is dry, we brush off any excess aggregate and continue with the application of the second layer of the MARIPUR 7100.


MARIPUR 7100 is supplied in 20 kg, 10 kg, 5 kg and 1kg pails. Pails should be stored in dry and cool rooms for up to 9months. Protect the material against moisture and direct sunlight. Storage temperature: 5-30C. Products should remain in their original, unopened containers, bearing the manufacturers name, product designation, batch number and application precaution labels.

Safety measures

MARIPUR 7100 contains isocyanates. See information supplied by the manufacturer. Flammable. Please study the Safety Datasheet. PROFESSIONAL USE ONLY.

Maripur 7100



also purchased with

    Your Cart
    Your cart is emptyReturn to Shop